Hey guys,
I got another question: I had to tear my motor out of the frame to replace a case bolt that happened to fall out (threads were gone on the case), put it back in, and I am wondering about the compensting sprocket. Which way does the spring wind when facing the motor? I cannot find a pic in either of my books, one Clymer's and the other an original HD manual. Should it be like a left-hand thread? So as the motor turns it pushes in? A photo would be nice.
Thanks
compensating sprocket
-
- Inactive member
- Member
- Posts: 38
- Joined: Wed Dec 10, 2008 8:02 am
- Bikes: '59 Pan/Shovel FLH
'06 Road King FLHR - Location: Bremerton Wa
-
- Senior Member
- Posts: 2082
- Joined: Fri Sep 21, 2007 3:03 am
- Bikes: '52 FL
'64 FLH - Has thanked: 163 times
- Been thanked: 511 times
Re: compensating sprocket
The spring will "wind" in the same direction, no matter which way you put it on.
Check it out, you will see what i mean.
Check it out, you will see what i mean.
-
- Member
- Posts: 51
- Joined: Sun Nov 08, 2015 10:46 pm
- Bikes: Harley Davidson 1959 FL Panhead 1964 FLH
- Location: Irvine CA
- Been thanked: 1 time
Re: compensating sprocket
Hey Guys,
I'm ready to install my compensating sprocket nut on my 1959 FL and was not sure If I was to apply any grease to the main shaft, inside the compensating sprocket nut and the woodruff key that fits into the main shaft keyway? Clymer manual does not mention applying grease when fitting the compensating sprocket nut back on. It would make sense to me that grease should be applied for easy installation and also when disassembly or removal for the sprocket nut am I correct?
Thank you,
Joey
I'm ready to install my compensating sprocket nut on my 1959 FL and was not sure If I was to apply any grease to the main shaft, inside the compensating sprocket nut and the woodruff key that fits into the main shaft keyway? Clymer manual does not mention applying grease when fitting the compensating sprocket nut back on. It would make sense to me that grease should be applied for easy installation and also when disassembly or removal for the sprocket nut am I correct?
Thank you,
Joey
-
- Moderator
- Senior Member
- Posts: 8378
- Joined: Sat Nov 15, 2008 4:09 am
- Bikes: Multiple H-D, Ducati, BMW, Triumph, BSA,...
- Has thanked: 478 times
- Been thanked: 2934 times
Re: compensating sprocket
A '59 doesn't have any woodruff keys on the drive end of the shaft.... What exactly do you have? How about a picture of it? And anything that has a key and a taper connection must be assembled absolutely dry and clean, no grease ever.
-
- Member
- Posts: 51
- Joined: Sun Nov 08, 2015 10:46 pm
- Bikes: Harley Davidson 1959 FL Panhead 1964 FLH
- Location: Irvine CA
- Been thanked: 1 time
Re: compensating sprocket
Rubone,
Sorry, I was incorrect on the woodruff key which this applies to the clutch hub and not the compensating sprocket nut. The diagram attach is a complete duplicate of my compensating sprocket nut that I have right now. So, just to confirm there is no grease applied to either the compensating sprocket or clutch hub when installing?
Joey
Sorry, I was incorrect on the woodruff key which this applies to the clutch hub and not the compensating sprocket nut. The diagram attach is a complete duplicate of my compensating sprocket nut that I have right now. So, just to confirm there is no grease applied to either the compensating sprocket or clutch hub when installing?
Joey
You do not have the required permissions to view the files attached to this post.
-
- Moderator
- Senior Member
- Posts: 8378
- Joined: Sat Nov 15, 2008 4:09 am
- Bikes: Multiple H-D, Ducati, BMW, Triumph, BSA,...
- Has thanked: 478 times
- Been thanked: 2934 times
Re: compensating sprocket
Clean and dry on the clutch hub to shaft, the key is primarily an indexing tool, the hub fit to shaft when tight is what keeps the parts together. A light film of grease on the splines to hub for compensator, and a heavier coat of grease on the cams and sleeve within the compensator.
-
- Member
- Posts: 51
- Joined: Sun Nov 08, 2015 10:46 pm
- Bikes: Harley Davidson 1959 FL Panhead 1964 FLH
- Location: Irvine CA
- Been thanked: 1 time
Re: compensating sprocket Nut
Thanks Rubone for the clarifications and specifications in regards to both the clutch hub and compensating sprocket nut.
Cheers,
Joey
Cheers,
Joey