Running on front cylinder only
-
- Member
- Posts: 412
- Joined: Fri Aug 23, 2002 10:05 pm
Running on front cylinder only
If a panhead has spark and 95 psi compression in both cylinders, what could cause it to run only on the front cylinder?
Re: Running on front cylinder only
I have had this problem. Turned out that one of the pushrod lock nuts had loosened off and the pusrod adjuster had screwed itself in so the valve would not open. Haggis encountered the same thing recently. I've heard that a spark plug can test okay in the open, but when screwed back into the motor will fail under compression. I have not come across this, but worth trying a new plug if you have not already done so.
-
- Member
- Posts: 412
- Joined: Fri Aug 23, 2002 10:05 pm
Re: Running on front cylinder only
I had to leave the bike in a small-town bike shop a day's ride away. That was a week ago, I called today and they said it's ready. Will post what I learn.
-
- Inactive member
- Member
- Posts: 55
- Joined: Sat May 31, 2003 9:57 pm
Re: Running on front cylinder only
I have also had the pushrod locknut problem. Didn't think much of it, and thought it was a flukey thing. Perhaps I ought to rethink that now.
Cotton, have you seen a lot of this?
Cotton, have you seen a lot of this?
-
- Senior Member
- Posts: 6937
- Joined: Sun Feb 10, 2002 2:30 am
- Bikes: -
- Location: Central Illinois
- Has thanked: 112 times
- Been thanked: 310 times
Re: Running on front cylinder only
Uh,...no.
Normally, the adjustors are a very dependable and stable design, unless abused.
I've seen bent rods, broken rods, lotsa knarfed lock nuts and threads from over-tightening, etc.,...but otherwise, the only times I have seen rods drastically go out of adjustment was when fresh motors would beat a valve into a poorly cut seat, thus tightening the rod to where a valve would hang open; the opposite of what has been described.
Unless a valve is sticking or something gets under the valve, it is hard to think of a way it would loosen.
Beware of '48, maybe '49 rockerarms that had cups that would loosen.
Normally, the adjustors are a very dependable and stable design, unless abused.
I've seen bent rods, broken rods, lotsa knarfed lock nuts and threads from over-tightening, etc.,...but otherwise, the only times I have seen rods drastically go out of adjustment was when fresh motors would beat a valve into a poorly cut seat, thus tightening the rod to where a valve would hang open; the opposite of what has been described.
Unless a valve is sticking or something gets under the valve, it is hard to think of a way it would loosen.
Beware of '48, maybe '49 rockerarms that had cups that would loosen.
-
- Member
- Posts: 24
- Joined: Mon Mar 18, 2013 2:21 pm
- Bikes: 56 Pan, 62 CH
- Been thanked: 2 times
Re: Running on front cylinder only
Check for spark . Swap the spark plug wires at the coil. You may now find the rear not firing. Swap the plugs?
-
- Former member
- Senior Member
- Posts: 3336
- Joined: Sat Jun 26, 2010 1:54 pm
- Bikes: 1958flh 1969sporty,had a knuckle but sold back to original owner
- Location: NEW JERSEY
- Has thanked: 195 times
- Been thanked: 278 times
Re: Running on front cylinder only
GUYS doesent anybody use glypt on yer screws?-Never should a pushrod scrw itself up the tube!If yer running solids there are things to handle that POUNDING over & over--HYD are SWEET!,But im a solid tappet runner,always have been,just like to have things my way & I know about it.---spend time & pop the tubes watch the movement up & down put tubes on CORKS OLNY!--Have fun yer lucky thats all that happened!-(10 min of pleasure looking at pushrods go).& No mishaps in the back of your mind!---respectfuly----RICHIE