best points and condenser for panhead
-
- Member
- Posts: 77
- Joined: Wed Mar 21, 2007 5:48 pm
- Bikes: 1950 FL
- Location: Seattle
- Has thanked: 4 times
- Been thanked: 14 times
best points and condenser for panhead
Have a stock 1950 panhead. What is the best brand of points and condenser to use? Where can they be purchased?
-
- Moderator
- Senior Member
- Posts: 3711
- Joined: Mon Dec 01, 2003 11:38 pm
- Bikes: '42 WLA X 2, '55FL, '93 Ultra Classic, '91 Fatboy, '97 883, '03 Rokon Trailbreaker, '83 GPz 750.
- Has thanked: 70 times
- Been thanked: 128 times
Re: best points and condenser for panhead
i have had good luck with blue streak parts.
http://www.jpcycles.com/productgroup.as ... bluestreak
i just did a tune up on a buddy's 63 FLH using oem harley parts with good success. the points harley sells seem of lesser quality due to the fiber insulator where the points pivot. just my personal taste i guess.
either one will work.
john
http://www.jpcycles.com/productgroup.as ... bluestreak
i just did a tune up on a buddy's 63 FLH using oem harley parts with good success. the points harley sells seem of lesser quality due to the fiber insulator where the points pivot. just my personal taste i guess.
either one will work.
john
-
- Senior Member
- Posts: 1014
- Joined: Fri Apr 18, 2003 12:26 pm
- Bikes: *
- Location: Sultan, WASH
- Been thanked: 6 times
- Contact:
Re: best points and condenser for panhead
napa has them....
the set on the right, has a much bigger contact surface
numbers are for points and condenser
mbskeam
the set on the right, has a much bigger contact surface
numbers are for points and condenser
mbskeam
-
- Member
- Posts: 13
- Joined: Thu Mar 27, 2008 10:06 pm
- Bikes: 1957 FLH Hand Shift
2015 Ultra Low - Location: Northern California
Re: best points and condenser for panhead
I recently tried to install a set of points from Drag Specialties on my '57. The bushing is about .003" too small to fit over the post. Also a very small contact area.
Perry
Perry
-
- Panhead Register Member
- Member
- Posts: 334
- Joined: Sun Sep 10, 2006 4:46 am
- Bikes: 1917F
1923JD
1928JD
1929JD
1929 Indian Four cyl
1954 Harley FL
2007 FLHTC - Location: "Big Timber Country" Western Canada
- Has thanked: 1 time
- Been thanked: 9 times
- Contact:
Re: best points and condenser for panhead
Does any one know if Delco Remy is still in buisness? I believe they were the original supplier for Harley Panhead contact points of the fiftys/sixtys. Same point set as Chev and GMC used at that time. Any confirmation?...Joe
Re: best points and condenser for panhead
IMO, if you can get a part that works correctly from NAPA............go with NAPA. Thanks for the pics and part numbers mbskeam. Deluxe.
-
- Inactive member
- Member
- Posts: 247
- Joined: Sat Aug 13, 2005 1:28 am
- Bikes: *
- Has thanked: 1 time
- Been thanked: 10 times
Re: best points and condenser for panhead
Just to throw this out there. I have a set of points that are supposed to be high quality, for pans, pt. # 30605-48(A)? Made by a German company. I don't know if this is the name of the company, or something else, but it says SCHIER-KONTAKTE on the label, #2612. They have a full length contact patch. I haven't had to use them yet. A friend of mine with a '52 had problems with some of the aftermarket points he bought. The diameter of the pivot was too small. They wouldn't move. Good luck!
Mike
Mike
-
- Member
- Posts: 80
- Joined: Fri Aug 29, 2008 3:04 pm
- Bikes: 1948 EL
1965 FLH
1966 FLH
1980 FLT Semi-Custom - Location: Chicago area
- Has thanked: 1 time
- Been thanked: 20 times
Re: best points and condenser for panhead
Hi John,
Have you used these blue streak points in an older bike? I have searched long and hard but have only been able to find the blue streak brand for 1970-E1978 models and that is what is listed at this link:
http://www.jpcycles.com/productgroup.as ... bluestreak
I used to put them in my 1965 Chevy pickup and would like to find some that fit my bikes (1966 FLH and1948 EL) but have been coming up empty.
The condenser is listed for models 1930-E1978 but not the points. I will try the NAPA brand!
Gitguy
Have you used these blue streak points in an older bike? I have searched long and hard but have only been able to find the blue streak brand for 1970-E1978 models and that is what is listed at this link:
http://www.jpcycles.com/productgroup.as ... bluestreak
I used to put them in my 1965 Chevy pickup and would like to find some that fit my bikes (1966 FLH and1948 EL) but have been coming up empty.
The condenser is listed for models 1930-E1978 but not the points. I will try the NAPA brand!
Gitguy
-
- Senior Member
- Posts: 2087
- Joined: Fri May 24, 2002 1:00 am
- Bikes: 64FL 99FLHR 01FXSTD
- Location: Mpls. MN.
- Has thanked: 72 times
- Been thanked: 145 times
Re: best points and condenser for panhead
I personally prefer the point set with the nut and bolt type terminal for the lead attatchment, I've had the wire slip out from under the spring band on the cheaper type. Mike
Re: best points and condenser for panhead
That would be the NAPA CS788. Have you used a set of these in 6V setup yet ? (yes, voltage doesn't matter, but I want them to be 6V worthy) Are they proven performers? I trust the nut terminal too, not an electrical slip joint.
I wish NAPA would buy out the entire OHV antique aftermarket.
I wish NAPA would buy out the entire OHV antique aftermarket.
Good tip -Open it at the counter. We know where and how to get points and condensers now.I have a set (with the stud & nut terminal) running in my stock 6 volt '49 pan right now, they seem to fit and function just fine.
Last edited by VT on Mon Oct 06, 2008 2:48 am, edited 1 time in total.
-
- Senior Member
- Posts: 2677
- Joined: Sat May 29, 2004 8:21 am
- Bikes: '31 VL, '34 VD, '45 WLA, '47 WL, '49 FL, '51 WL, '58 ST (Hummer), '71 GE (Servi)
- Location: Lonoke, Arkansas
- Has thanked: 5 times
- Been thanked: 49 times
Re: best points and condenser for panhead
VT,
Both those contact sets (CS) are CS 788, you never know what is going to come out of those old Echlin boxes because the parts have been around for years and probably repackaged several times. You have to open the box at the store and make sure its the style you like because they could be either one. The RR 176 is the condensor.
Both those numbers cross to Standard Motor Products (SMP) parts. The points are DR-2240X, the condensor is DR-90X.
I have a set (with the stud & nut terminal) running in my stock 6 volt '49 pan right now, they seem to fit and function just fine.
mike
Both those contact sets (CS) are CS 788, you never know what is going to come out of those old Echlin boxes because the parts have been around for years and probably repackaged several times. You have to open the box at the store and make sure its the style you like because they could be either one. The RR 176 is the condensor.
Both those numbers cross to Standard Motor Products (SMP) parts. The points are DR-2240X, the condensor is DR-90X.
I have a set (with the stud & nut terminal) running in my stock 6 volt '49 pan right now, they seem to fit and function just fine.
mike
-
- Member
- Posts: 127
- Joined: Mon Oct 02, 2006 9:55 pm
- Bikes: 56 FL, 07 Goldwing ,91 BMW K75
- Has thanked: 8 times
- Been thanked: 7 times
Re: best points and condenser for panhead
I use Harley points,condensers and plugs bought at my local dealer. It is a tune up kit that is listed in the current accessory cataloge for $20.00.
-
- Member
- Posts: 77
- Joined: Wed Mar 21, 2007 5:48 pm
- Bikes: 1950 FL
- Location: Seattle
- Has thanked: 4 times
- Been thanked: 14 times
Re: best points and condenser for panhead
Thank you for all of the information. I went to the local Napa store, my favorite store in town, and the store actually had a set of CS788 points. However, upon looking at them, they would not fit on my circuit breaker plate. My plate, from a 1950 FL, has a vertical stud over which the points fit. The CS788 do not have a hole in the points such that they would not fit over the stud. The CS788 points require the later type of circuit breaker plate where the points fit into an indent in the plate. Regardless, I bought a set of Echlin points that fit, CS763P, with matching condenser RR174.
I don't know about you guys, but I lay awake at night thinking about important things like as follows: The "P" designation at the end of the points part number means that one of the points surfaces is "pierced." It has a 1/16" hole in the middle of the contact surface. I suppose that this is to prevent buildup on the surface. Has anyone tried this type of points? Thanks.
I don't know about you guys, but I lay awake at night thinking about important things like as follows: The "P" designation at the end of the points part number means that one of the points surfaces is "pierced." It has a 1/16" hole in the middle of the contact surface. I suppose that this is to prevent buildup on the surface. Has anyone tried this type of points? Thanks.
Re: best points and condenser for panhead
These issues are all that's worth pondering. I'd like to get to the bottom of all this - with a points and condenser all of we OEM style timer people can use.Regardless, I bought a set of Echlin points that fit, CS763P, with matching condenser RR174.
I don't know about you guys, but I lay awake at night thinking about important things like as follows: The "P" designation at the end of the points part number means that one of the points surfaces is "pierced." It has a 1/16" hole in the middle of the contact surface. I suppose that this is to prevent buildup on the surface. Has anyone tried this type of points? Thanks.