4 speed Trans gasket seals kit recommendation
-
- Member
- Posts: 17
- Joined: Thu Jan 12, 2017 6:36 pm
- Bikes: 1951 Panhead FL
- Location: Michigan
4 speed Trans gasket seals kit recommendation
Hi Guys,
Just seeing what gasket seal kits you find to be most useful and successful . Jims etc.
Thanks Chris
Just seeing what gasket seal kits you find to be most useful and successful . Jims etc.
Thanks Chris
-
- Senior Member
- Posts: 2405
- Joined: Wed Jul 07, 2010 4:28 am
- Bikes: 1950Panhead
- Location: USA
- Has thanked: 1 time
- Been thanked: 366 times
-
- Former member
- Senior Member
- Posts: 2789
- Joined: Tue Dec 18, 2007 2:10 pm
- Bikes: 1941/59 EL
1952 FL
1977 FLH
1994 Fatboy - Has thanked: 22 times
- Been thanked: 110 times
Re: 4 speed Trans gasket seals kit recommendation
Not "Jims", but "James". Pretty much cannot go wrong with James, anywhere on the motorcycle.Wilson wrote:Hi Guys,
Just seeing what gasket seal kits you find to be most useful and successful . Jims etc.
Thanks Chris
-
- Member
- Posts: 17
- Joined: Thu Jan 12, 2017 6:36 pm
- Bikes: 1951 Panhead FL
- Location: Michigan
Re: 4 speed Trans gasket seals kit recommendation
So the main gear has no seal in the end does it not need one or I am missing something Trans is a 1951
-
- Site sponsor
- Senior Member
- Posts: 1922
- Joined: Fri Jul 01, 2011 8:43 pm
- Bikes: 1969 FLF
1937 EL
1940 U - Location: san diego
- Has thanked: 1478 times
- Been thanked: 243 times
Re: 4 speed Trans gasket seals kit recommendation
g3et the manual, do your homework, then you will know your scoot, from the inside out.
Wilson wrote:So the main gear has no seal in the end does it not need one or I am missing something Trans is a 1951
-
- Moderator
- Senior Member
- Posts: 8406
- Joined: Sat Nov 15, 2008 4:09 am
- Bikes: Multiple H-D, Ducati, BMW, Triumph, BSA,...
- Has thanked: 481 times
- Been thanked: 2955 times
-
- Member
- Posts: 64
- Joined: Tue Sep 06, 2016 9:27 pm
- Bikes: '77 XLCR, '74 FLH, '64 DuoGlide
- Location: Walthill, Nebraska
- Been thanked: 4 times
- Contact:
Re: 4 speed Trans gasket seals kit recommendation
There's a way to put a seal there but the shaft has to be machined to accept it. If you go to that much work, make it deep enough to accept two seals. Saddlebagrail has a fix for the spacer too, and puts an o-ring in there to keep the sprocket splines from seeping. Right now I'm doing a '64 that was leaking out the kicker shaft. There's a seal there but the bushings were worn enough that a new seal couldn't do its job so I'm fabricating new undersized bushings to fit the kicker shaft like they should (only about .005" smaller), then the seal will work. Sometimes I put an o-ring groove in the clutch shaft bushing to keep water from running down the shaft and contaminating the oil too. I use a very small o-ring so the groove doesn't have to be very deep.
-
- Former member
- Senior Member
- Posts: 3336
- Joined: Sat Jun 26, 2010 1:54 pm
- Bikes: 1958flh 1969sporty,had a knuckle but sold back to original owner
- Location: NEW JERSEY
- Has thanked: 195 times
- Been thanked: 278 times
Re: 4 speed Trans gasket seals kit recommendation
If Tranny is in Good condition after overhaul//Theres really no need for any custom made nuts or anything on the shaft!//(I am in no way saying RAYS fix is not good!!//I think it is a pretty great fix for a F--ked-up mixer!)//I have been running a 44 mixer & anytime I have to service anything/(which is usually broken pawl springs/& I log on Alot of miles,& run ST.60wt in it).Then I clean the mainshaft area (REAL-GOOD)/to eat off it stage.Then This is the olny area that I use Sillycone other then the EX. spigots on the bike!//The trick is all in the PREP-WORK!//& All Sillycone must be TOOLED & allowed to dry overnite in a warm garage or house//It can take sillycone up to a month to cure all the way!!!!!/IN COLD WEATHER.Also I use a sillycone in this area that most cannot get!/Im a Glazier by trade & use 795-structural sealent by DOW Corning.Kenseal in Carlstadt NJ is a supplier.But It cannot be purchased in single 10oz. cartridgeges,olny by the case which is $500+!.Also its not good for EX. spigots as it will cook off!//But for the tranny it works Wonders!//I have been applying this to the area for MANY YRS./& never had trouble with leaks!.However this is not the olny sealent you can use!--Any Good RTV-Sillycone will get the job done!--(As long as the area is PREPPED properly).Not to stir the pot so to say//O-rings added where not originally intended /end-up in the mixer eventually!!//I have seen this quite a few times over the yrs.//Best thing is just change out the bush,& ream to size!//But if insisting on another homebrew fix//I have seen a TEFLON seal with a SS-spring in the center of it work!--The seal is .250 wide with walls that rise up -with the spring in the middle/Instead of just a light seat cut ,like for an o-ring/it requires that a little turning on a lathe be done & not deep!//These I never saw break apart!--(YET).---Respectfully----Richie
-
- Former member
- Senior Member
- Posts: 2789
- Joined: Tue Dec 18, 2007 2:10 pm
- Bikes: 1941/59 EL
1952 FL
1977 FLH
1994 Fatboy - Has thanked: 22 times
- Been thanked: 110 times
Re: 4 speed Trans gasket seals kit recommendation
Dow Corning 795 in single cartridges can be found almost anywhere.
http://www.dkhardware.com/product-19838 ... fgodzDMJbA
http://www.dkhardware.com/product-19838 ... fgodzDMJbA