More Top End
-
- Member
- Posts: 63
- Joined: Fri Jan 27, 2006 2:11 am
- Bikes: 42 Flathead U, 53 Panhead, 2011 Roadglide
- Location: Chino Valley, AZ
- Has thanked: 2 times
- Been thanked: 1 time
More Top End
This is a 53 Panhead with a enclosed belt drive. I have a 24 tooth trans sprocket and a 51 tooth rear sprocket, The engine sprocket is 39 and the clutch is 62. I think I calculated this before and have a ratio of 3.38. I feel comfortable at 55-60 mph with this but would like to get at least another 5mph at the top end. Would changing the trans sprocket to a 25 tooth accomplish this? Can you gain about 5mph per tooth, at the same rpm?
Thanks!
Thanks!
Re: More Top End
If you get much bigger with your gears, you're gonna have a hard time getting the bike moving without slipping the clutch...
VPH-D
VPH-D
-
- Member
- Posts: 51
- Joined: Thu Jan 26, 2006 1:21 am
- Bikes: 1965 Panhead chopper
2001 Roadking Stage IV - Location: Oklahoma City OK
- Has thanked: 6 times
- Been thanked: 1 time
Re: More Top End
The 25 tooth will also possibly chew into the clutch arm on the tranny. I run 25 tranny and 47 rear wheel and O-Ring chain and the arm has been chewed. I jus weld it up when I have to. My objective is to keep overall engine speed down and with the 4 3/4 arm I really need to watch the piston speeds.
-
- Moderator
- Senior Member
- Posts: 8411
- Joined: Sat Nov 15, 2008 4:09 am
- Bikes: Multiple H-D, Ducati, BMW, Triumph, BSA,...
- Has thanked: 483 times
- Been thanked: 2958 times
Re: More Top End
Spin it faster...
Why is everyone so afraid of RPM. Engines work well and last long when spun into their sweet spot, and it isn't about loping...
Lugging an engine will kill it just as fast as over revving.
As for the 4-3/4 inch arm. I liked to bounce my 4-3/4 inch stroke off the 7K mark on the tach for shifting...
All this fear of piston speed, torque specs, highway RPM, has taken all the fun out of riding .
Ride it like you stole it and quit worrying.
Why is everyone so afraid of RPM. Engines work well and last long when spun into their sweet spot, and it isn't about loping...
Lugging an engine will kill it just as fast as over revving.
As for the 4-3/4 inch arm. I liked to bounce my 4-3/4 inch stroke off the 7K mark on the tach for shifting...
All this fear of piston speed, torque specs, highway RPM, has taken all the fun out of riding .
Ride it like you stole it and quit worrying.
-
- Member
- Posts: 51
- Joined: Thu Jan 26, 2006 1:21 am
- Bikes: 1965 Panhead chopper
2001 Roadking Stage IV - Location: Oklahoma City OK
- Has thanked: 6 times
- Been thanked: 1 time
Re: More Top End
Rubone...You obviously have more money than I do. I prefer not to mistreat my equipment.
-
- Moderator
- Senior Member
- Posts: 8411
- Joined: Sat Nov 15, 2008 4:09 am
- Bikes: Multiple H-D, Ducati, BMW, Triumph, BSA,...
- Has thanked: 483 times
- Been thanked: 2958 times
-
- Member
- Posts: 253
- Joined: Sun Dec 16, 2012 8:52 am
- Bikes: 94FLSTN
63FLH - Has thanked: 67 times
- Been thanked: 36 times
Re: More Top End
Running standard everything except for belt drive.
ie 22 T front sprocket and sweet spot 65-70 MPH.
Thinking about going up to 23T when chains and sprocket need replace.
Maybe sweet spot 70-75 MPH.
Regards B.B.
ie 22 T front sprocket and sweet spot 65-70 MPH.
Thinking about going up to 23T when chains and sprocket need replace.
Maybe sweet spot 70-75 MPH.
Regards B.B.
-
- Senior Member
- Posts: 1507
- Joined: Wed May 09, 2001 11:02 pm
- Bikes: 50 EL chopper
44 U that looks like a 37.
60 FLH (Sold)
59 FLH (Sold)
58 FL (Sold)
08 CVO Road King - Location: Maryland
- Has thanked: 244 times
- Been thanked: 138 times
Re: More Top End
It is my understanding that the balance factor changes the sweet spot. These motors wind up just fine. They do like the RPMs. I wouldn't go too tall with the gearing either. You just loose all the balls your motor can provide for top end. No more fun in the mountains.
-
- Member
- Posts: 172
- Joined: Sun Nov 30, 2014 2:33 am
- Bikes: 1957 FL. Was very original but is now sold.
58 PanShovel - Location: Brixton London
- Has thanked: 46 times
- Been thanked: 2 times
- Contact:
Re: More Top End
RUBONE wrote:Spin it faster...
Why is everyone so afraid of RPM. Engines work well and last long when spun into their sweet spot, and it isn't about loping...
Lugging an engine will kill it just as fast as over revving.
As for the 4-3/4 inch arm. I liked to bounce my 4-3/4 inch stroke off the 7K mark on the tach for shifting...
All this fear of piston speed, torque specs, highway RPM, has taken all the fun out of riding .
Ride it like you stole it and quit worrying.
when i have gotten back home after a good trash out on mine its normally running better than ever. You don't have to baby them! Ride em.
-
- Member
- Posts: 63
- Joined: Fri Jan 27, 2006 2:11 am
- Bikes: 42 Flathead U, 53 Panhead, 2011 Roadglide
- Location: Chino Valley, AZ
- Has thanked: 2 times
- Been thanked: 1 time
Re: More Top End
OK, Thanks for all the response. My wife and I just did a 1600 mile trip and tried to keep it around 60 most of the way. The vibration just seems so intense when I hit 65 or 70, the wife gets upset as there is so much vibration on her footpegs and I notice it as well on the floorboards. I will try to see if I can find a sweet spot over the 70 mph.
-
- Former member
- Senior Member
- Posts: 3336
- Joined: Sat Jun 26, 2010 1:54 pm
- Bikes: 1958flh 1969sporty,had a knuckle but sold back to original owner
- Location: NEW JERSEY
- Has thanked: 195 times
- Been thanked: 278 times
Re: More Top End
Gilb-----I have been saying this to alot of guys!--As Rubone said--If your comfy at 55-60---Then Your motor (I believe is spinning low RPM)-Dont be afraid of 4000RPMS---This is where there INTENDED FACTORY DESIGN is meant for!.Doing 70mph at 3500Rpm--IS LUGGING!--NO GOOD ,Maybe it feels better to you ,But the motor Dont like it & You will actually end-up SERVICING your bike MORE!.I run a chain,24T-compensater/ 24T-Mixer-51Rear.I pass at 90MPH-Also I have no off-line issues!.Spin it & frequent OIL CHANGES/& weekly look over is all thats required to have a daily SUCESSFUL RUNNER!.I wouldnt give you bad or a STORY of INFO!.IM telling you from actual EXP.---Anybody Here that REALLY uses thier machines for DECADES,Become familier with every quirk the machines have!.I use to want lower RPM!--BUT MY POP said IF it were good for the design He would of changed it long ago!.I BUBBLETEST 1-Time a month!--sometimes nothing -other times a pinhole leak & a 1/2 turn on clamp its gone!--I just went from 2-kicks back to 1-kick!.The top-End on Pans is virtually indestructable!-(olny lack of oil can hurt them.And they dont lack!.Trust your skills man,that you no-doubt have & built a nice MOTOR/MIXER!---Let her spin----Check this out-(T-Monster wheels/Much heavier & there spinning & most important LASTING without damage--Even Strokers to 84-inch are totaly safe daily runners!).--Respectfully----Richie
-
- Member
- Posts: 274
- Joined: Tue Mar 27, 2012 3:13 pm
- Bikes: 1945EL project
1962FLH
1974FLH - Location: Central Texas
- Has thanked: 41 times
- Been thanked: 37 times
- Contact:
Re: More Top End
From what you are saying it sounds like the motivation for the Drivetrain ratio change is excessive vibration. Drivetrain ratio change does not make excessive vibration go away. Just forces you to put up with it at a different speed. Excessive vibration is not normal. Excessive vibration will break motor mounts and frames and cause things to fall off. I would find and address the cause of the vibration before gearing up.
Good luck with it.
John
Good luck with it.
John
Re: More Top End
It just occurred to me that your speedo is about 10 mph off, because of your 24 tooth trans sprocket. You're not going 60 when the speedo says so...
VPH-D
VPH-D