Linkert Carb blows gas out of the overflow relief hole.
Linkert Carb blows gas out of the overflow relief hole.
When I prime-kick my '56 with full choke, it spurts a noticeable amount of gas out of the overflow hole (just above the float bowl, on the throttle body facing the rear cylinder).
Gas also is forced out past the low-speed needle if I block the overflow hole with my finger while kicking with full choke. Once the engine is running, there is no further gas leak. The only reason it concerns me is that the bike is not the best of starters, and I am wondering if the gas is being blown out of the hole instead of being sucked into the engine while priming.
Apart from this, the engine runs great. I did try blocking the overflow hole with a grommet, it started well but ran very rough on the road, I think with fuel starvation.
4,000 miles ago I rebuilt the engine with a new piston, new Vtwin barrels, new STD heads (awesome!).
I have only just started to notice this as I have recently fitted a smaller tank, and can see it happening. It has probably been doing this for thousands of miles.
Gas also is forced out past the low-speed needle if I block the overflow hole with my finger while kicking with full choke. Once the engine is running, there is no further gas leak. The only reason it concerns me is that the bike is not the best of starters, and I am wondering if the gas is being blown out of the hole instead of being sucked into the engine while priming.
Apart from this, the engine runs great. I did try blocking the overflow hole with a grommet, it started well but ran very rough on the road, I think with fuel starvation.
4,000 miles ago I rebuilt the engine with a new piston, new Vtwin barrels, new STD heads (awesome!).
I have only just started to notice this as I have recently fitted a smaller tank, and can see it happening. It has probably been doing this for thousands of miles.
-
- Moderator
- Senior Member
- Posts: 3711
- Joined: Mon Dec 01, 2003 11:38 pm
- Bikes: '42 WLA X 2, '55FL, '93 Ultra Classic, '91 Fatboy, '97 883, '03 Rokon Trailbreaker, '83 GPz 750.
- Has thanked: 70 times
- Been thanked: 128 times
Re: Linkert Carb blows gas out of the overflow relief hole.
Pete,
It sounds like you need to pull your float bowl off and see what the float is set at. Also what condition it is in.
john
It sounds like you need to pull your float bowl off and see what the float is set at. Also what condition it is in.
john
-
- Former member
- Senior Member
- Posts: 3332
- Joined: Sat Jun 26, 2010 1:54 pm
- Bikes: 1958flh 1969sporty,had a knuckle but sold back to original owner
- Location: NEW JERSEY
- Has thanked: 195 times
- Been thanked: 277 times
Re: Linkert Carb blows gas out of the overflow relief hole.
PETE--I am not an expert on linkerts!-(I get by with help on this K-BASE!)-Anyway I did see a hole that was .250 on a linkert that was somebodies attempt at --I DONT KNOW!-PERFORMANCE??)--Anyway I did manage to fix this leaker by threading in a small mainjet!-(like an airbleed).The JET was small enuff to not leak & allowed sumping while Prime-KICKING!.---Guys here are real GOOD with issues as yours & PICS. are really good to post!---Respectfully---RICHIE
-
- Senior Member
- Posts: 6937
- Joined: Sun Feb 10, 2002 2:30 am
- Bikes: -
- Location: Central Illinois
- Has thanked: 112 times
- Been thanked: 310 times
Re: Linkert Carb blows gas out of the overflow relief hole.
Pete!
The overflow hole cannot be blocked because it also vents the headspace above the fuel.
John and 1962FLH may both be right.
If the float isn't floating, and the fuel level is too high, then overlap from a rad cam could cause reversion that ordinarily would be relieved at the mouth of the carb, but is blocked by the choke, thus pressurizing the bowl.
Beware of heavy floats, whether brass, gas-logged corks, or certain new nitrophyll productions from an Indian distributor.
Let us know what you find inside,
...Cotten
The overflow hole cannot be blocked because it also vents the headspace above the fuel.
John and 1962FLH may both be right.
If the float isn't floating, and the fuel level is too high, then overlap from a rad cam could cause reversion that ordinarily would be relieved at the mouth of the carb, but is blocked by the choke, thus pressurizing the bowl.
Beware of heavy floats, whether brass, gas-logged corks, or certain new nitrophyll productions from an Indian distributor.
Let us know what you find inside,
...Cotten
-
- Member
- Posts: 274
- Joined: Tue Mar 27, 2012 3:13 pm
- Bikes: 1945EL project
1962FLH
1974FLH - Location: Central Texas
- Has thanked: 41 times
- Been thanked: 37 times
- Contact:
Re: Linkert Carb blows gas out of the overflow relief hole.
If you run a performance Cam with lots of overlap; the intake and exhaust valves are open at the same time for long enough duration to push air into the carb bowl through the main nozzle with the choke closed. Block the vent hole and it will find another place to relive the pressure. However As John stated check your float adjustment; when set correctly this should not be noticeable.
Re: Linkert Carb blows gas out of the overflow relief hole.
Thanks for all the replies.
Checked the float today, it was a fraction high but good condition foam. I set it right but the blowback continues. I also wondered about cam, but it's a standardish Andrews as far as I can remember, and anyway the blowback only happens on full choke. 3/4 choke, no blowback. Like I say, it's not a serious problem, just seems to stop the cylinders fully priming, making starting procedures unreliable.
I also really gassed it at medium revs, 4th gear today, and there is no visible venting.
Checked the float today, it was a fraction high but good condition foam. I set it right but the blowback continues. I also wondered about cam, but it's a standardish Andrews as far as I can remember, and anyway the blowback only happens on full choke. 3/4 choke, no blowback. Like I say, it's not a serious problem, just seems to stop the cylinders fully priming, making starting procedures unreliable.
I also really gassed it at medium revs, 4th gear today, and there is no visible venting.
-
- Senior Member
- Posts: 522
- Joined: Wed Mar 01, 2006 10:14 pm
- Bikes: -
- Has thanked: 33 times
- Been thanked: 108 times
Re: Linkert Carb blows gas out of the overflow relief hole.
ALL of my Linkerts blow fuel out the vent when kicked over on full choke.
Re: Linkert Carb blows gas out of the overflow relief hole.
OK so now we know. It's supposed to do that!
Thanks Larry
Thanks Larry
-
- Senior Member
- Posts: 6937
- Joined: Sun Feb 10, 2002 2:30 am
- Bikes: -
- Location: Central Illinois
- Has thanked: 112 times
- Been thanked: 310 times
Re: Linkert Carb blows gas out of the overflow relief hole.
I beg to differ, Larry and Pete!
How far do your machines lean to the left on the jiffy stand?
....Cotten
How far do your machines lean to the left on the jiffy stand?
....Cotten
Re: Linkert Carb blows gas out of the overflow relief hole.
Mine is standard lean on the stand. I thought Larry had solved it!
-
- Senior Member
- Posts: 522
- Joined: Wed Mar 01, 2006 10:14 pm
- Bikes: -
- Has thanked: 33 times
- Been thanked: 108 times
Re: Linkert Carb blows gas out of the overflow relief hole.
The carburetors flood when kicked over repeatedly on full choke. Isn't that the described situation?
Re: Linkert Carb blows gas out of the overflow relief hole.
I prime with one kick on full choke. A small amount of gas spurts out of the overflow hole on compression stroke. Doesn't happen on 3/4 choke.
-
- Senior Member
- Posts: 6937
- Joined: Sun Feb 10, 2002 2:30 am
- Bikes: -
- Location: Central Illinois
- Has thanked: 112 times
- Been thanked: 310 times
Re: Linkert Carb blows gas out of the overflow relief hole.
Larry!
If you have to kick more than twice with the choke on.. its a starting issue!
Still, this is not a common complaint.
Flooding in itself is nearly always cured with a proper float and adjustment.
(Flooding while sitting is a petcock problem.)
Excessive kicking with the choke closed should still draw only into the bore of the carburetor.
To exit the overflow from the bowl, the fuel level must be far higher than proper, or forced out.
....Cotten
If you have to kick more than twice with the choke on.. its a starting issue!
Still, this is not a common complaint.
Flooding in itself is nearly always cured with a proper float and adjustment.
(Flooding while sitting is a petcock problem.)
Excessive kicking with the choke closed should still draw only into the bore of the carburetor.
To exit the overflow from the bowl, the fuel level must be far higher than proper, or forced out.
....Cotten
-
- Senior Member
- Posts: 6937
- Joined: Sun Feb 10, 2002 2:30 am
- Bikes: -
- Location: Central Illinois
- Has thanked: 112 times
- Been thanked: 310 times
Re: Linkert Carb blows gas out of the overflow relief hole.
A photo for clarity, Folks!
Note the white arrow shows a shallow hole drilled vertically into the 'roof' of the bowlchamber, and the black arrow shows the gallery drilled horizontally from the outside to intersect with the vertical hole. The fuel should be 5/8" of an inch from the 'roof' , when the machine is level.
If the machine is tilted to the left, the fuel gets much closer.
If the petcock leaks, it will be higher for a cold start.
If the float is not of proper buoyancy, the level will always be higher, leading to a rich condition.
....Cotten
Note the white arrow shows a shallow hole drilled vertically into the 'roof' of the bowlchamber, and the black arrow shows the gallery drilled horizontally from the outside to intersect with the vertical hole. The fuel should be 5/8" of an inch from the 'roof' , when the machine is level.
If the machine is tilted to the left, the fuel gets much closer.
If the petcock leaks, it will be higher for a cold start.
If the float is not of proper buoyancy, the level will always be higher, leading to a rich condition.
....Cotten
You do not have the required permissions to view the files attached to this post.