I'm going to use a knucklehead gear cover on my 58 gearcase.
Consequently I need to change the pinion bushing to the small one.
The book tells me to mount the bushing as deep as it can.
This would seat the bushing so the lubrication holes no longer align.
It would still be open but half the diameter would be covered.
Doesn't seem right.
Anyone has an actual reference from the gasket surface?
/Mikael
Pinion bushing seating depth
-
- Member
- Posts: 65
- Joined: Fri Feb 19, 2010 11:00 pm
- Bikes: 48EL
- Location: Sweden
- Has thanked: 8 times
- Been thanked: 6 times
-
- Moderator
- Senior Member
- Posts: 8414
- Joined: Sat Nov 15, 2008 4:09 am
- Bikes: Multiple H-D, Ducati, BMW, Triumph, BSA,...
- Has thanked: 484 times
- Been thanked: 2958 times
Re: Pinion bushing seating depth
The correct type cover for the small bushing has a step in it that the bushing stops against. The earlier cover does not. That is why it can go too deep. The stock bushing is set at approximately 1/8". (I measured it a .120")
Robbie
Robbie
-
- Former member
- Senior Member
- Posts: 3336
- Joined: Sat Jun 26, 2010 1:54 pm
- Bikes: 1958flh 1969sporty,had a knuckle but sold back to original owner
- Location: NEW JERSEY
- Has thanked: 195 times
- Been thanked: 278 times
Re: Pinion bushing seating depth
I just put a old knuck cover on my 58 in FEB.---I can tell you this ,the Eastern bering when its fitted at the correct depth --you will find the oil-holes will be partially blocked!-(both of them)--the feed you have to elongate the hole about .100-if memory serves me correctly,& the rear hole that on a 45-just run a bit thru it at the same angle!---Measure your clearences using the gover gasket that you will be using for sealing-up!--to take your end-play measurements!--remember try to get it to take 1-shim for proper clearance!--to many thin ones just disappear after awhile in the motor!---oh yea after you find the depth for your pinion bushing-use the pin & drill it a 1/32-deeper I put a drop of loc-tite & staked it back as should be.------RICHIE
-
- Member
- Posts: 165
- Joined: Fri Feb 04, 2011 11:18 am
- Bikes: 1975 FL, 2005 RoadKing, 1949 Panhead
- Location: Missouri
- Has thanked: 2 times
- Been thanked: 7 times
Re: Pinion bushing seating depth
Richie---Not sure i understand the response to this post. I also am using an early model cam cover on a later pan. To determine the correct depth, I was going to use gap measurement from bottom of old bushing and duplicate with new bushing (without flange). What do you mean about finding depth and one shim? Did not think this side had a shim and end play was set by spacer in timken bearings of left case.....Dennis
-
- Former member
- Senior Member
- Posts: 3336
- Joined: Sat Jun 26, 2010 1:54 pm
- Bikes: 1958flh 1969sporty,had a knuckle but sold back to original owner
- Location: NEW JERSEY
- Has thanked: 195 times
- Been thanked: 278 times
Re: Pinion bushing seating depth
Dennis---You are correct!--I was ahead of myself & thinking of cam & idler,etc.-endplay!--Sorry for the confusion.My Fault for not explaining it better!----RICHIE
-
- Member
- Posts: 165
- Joined: Fri Feb 04, 2011 11:18 am
- Bikes: 1975 FL, 2005 RoadKing, 1949 Panhead
- Location: Missouri
- Has thanked: 2 times
- Been thanked: 7 times
Re: Pinion bushing seating depth
Now that I have started to do this pinion fitting, I believe I will also double check by not only making sure the bushing hole lines up with the hole in the cover, but also ensure the hole in the shaft lines up with the hole in the bushing after the crank assembly is installed in the case. Dennis
-
- Former member
- Senior Member
- Posts: 3336
- Joined: Sat Jun 26, 2010 1:54 pm
- Bikes: 1958flh 1969sporty,had a knuckle but sold back to original owner
- Location: NEW JERSEY
- Has thanked: 195 times
- Been thanked: 278 times
Re: Pinion bushing seating depth
Clunker1--No doubt you will be scraping your pinion & others for correct fit!.Keep using the same cover gasket & put about 6-screws in the cover to hold it.--Just remember to color the insides of the bushings with a sharpie & give it a few turnovers.Pull the cover & there it is!---I have heard of guys using Reamers & homemade sanding mops--BIG NO for a SANDING-MOP,--Reamers work,BUT a MACHINIST-SCPRAPER will allow you to olny remove where needed & is a FAR BETTER choice in my personal opinion!--I prefer it as you may have to remove more on 1-side of the bushing-The SCRAPER gives you that freedom!-The Reamer will remove on the whole 360-degrees.I have used both & the Scraper may take longer-but the finished result is better!---respectfuly---RICHIE