WLDD Surfaces
-
- Member
- Posts: 45
- Joined: Sat Oct 25, 2008 6:37 pm
- Bikes: 49 FL
- Been thanked: 3 times
WLDD Surfaces
Hey Guys:
Can anyone tell me anything about the '39 WLDD? A shop near me has one for sale. The Palmer book does not even mention it. Online sources tell me that that production of this model was 267 in 1939 only. Specifically, can anyone tell me if the WLDD had cylinders with larger cooling fins and a four-bolt intake manifold with Linkert M-41? I would appreciate hearing from anyone who has information on these.
R.M.
Can anyone tell me anything about the '39 WLDD? A shop near me has one for sale. The Palmer book does not even mention it. Online sources tell me that that production of this model was 267 in 1939 only. Specifically, can anyone tell me if the WLDD had cylinders with larger cooling fins and a four-bolt intake manifold with Linkert M-41? I would appreciate hearing from anyone who has information on these.
R.M.
- Attachments
-
- 018_crop.jpg (266.75 KiB) Viewed 1808 times
-
- Senior Member
- Posts: 2405
- Joined: Wed Jul 07, 2010 4:28 am
- Bikes: 1950Panhead
- Location: USA
- Has thanked: 1 time
- Been thanked: 366 times
-
- Moderator
- Senior Member
- Posts: 8404
- Joined: Sat Nov 15, 2008 4:09 am
- Bikes: Multiple H-D, Ducati, BMW, Triumph, BSA,...
- Has thanked: 481 times
- Been thanked: 2954 times
Re: WLDD Surfaces
The WLDD stamping was the new WLD special for mid '39. It does not use a 4 bolt manifold, it uses the 3 bolt similar to the UL/ULH version. The biggest difference between it and the WLD was the Aluminum heads and the mid size ports. Note that no factory porting was done on this engine. They also used standard valves and cams.
-
- Member
- Posts: 45
- Joined: Sat Oct 25, 2008 6:37 pm
- Bikes: 49 FL
- Been thanked: 3 times
Re: WLDD Surfaces
Thanks for both replies.
Am I correct in thinking that the "deep fin cylinders" on the DD model were, like the aluminum cylinder heads, standard issue on later 45's?
Any ideas on what carburetor was fitted to the DD?
Am I correct in thinking that the "deep fin cylinders" on the DD model were, like the aluminum cylinder heads, standard issue on later 45's?
Any ideas on what carburetor was fitted to the DD?
-
- Moderator
- Senior Member
- Posts: 8404
- Joined: Sat Nov 15, 2008 4:09 am
- Bikes: Multiple H-D, Ducati, BMW, Triumph, BSA,...
- Has thanked: 481 times
- Been thanked: 2954 times
Re: WLDD Surfaces
No, the "deep fin" cylinders were only used on the WLD models in the '40s, WLs used the small fin cylinders. WLD cylinders are rare and very expensive!Am I correct in thinking that the "deep fin cylinders" on the DD model were, like the aluminum cylinder heads, standard issue on later 45's?
Robbie
-
- Senior Member
- Posts: 1500
- Joined: Tue Aug 03, 2010 7:10 pm
- Bikes: 1937 U big flathead, 88" stroker, dual port, big cams, pop-up pistons
- Location: Lynbrook, New York
- Has thanked: 32 times
- Been thanked: 387 times
- Contact:
Re: WLDD Surfaces
All 1936-73 "normal" cylinders, including commercial and military, solo and trike variants with both 3/8" and 7/16" bolts have casting numbers:
Front 120-36
Rear 120-361
All 1939-* "special" cylinders including WLD, WLDD, WLDR and WR variants have casting numbers:
Front 120-39
Rear 120-391
Front 120-36
Rear 120-361
All 1939-* "special" cylinders including WLD, WLDD, WLDR and WR variants have casting numbers:
Front 120-39
Rear 120-391
-
- Member
- Posts: 399
- Joined: Thu Feb 21, 2008 9:07 am
- Bikes: 42 WLC, 47 EL, 53 FLE, 62 FL, 78 FLH
- Location: British Columbia
- Has thanked: 1 time
- Been thanked: 20 times
Re: WLDD Surfaces
I posted a 1939 factory brochure here on the sight. Go to Documentation and then factory brochures and have a look to see if there's anything in it of use to you.
-
- Member
- Posts: 45
- Joined: Sat Oct 25, 2008 6:37 pm
- Bikes: 49 FL
- Been thanked: 3 times
Re: WLDD Surfaces
Thanks!
The '39 brochure does not mention the DD.
So the DD was a standard 45 except for the WLD cylinders and aluminum heads?
Being one of a production run of 269, is it worth a significant premium over over a WL now? R.M.
The '39 brochure does not mention the DD.
So the DD was a standard 45 except for the WLD cylinders and aluminum heads?
Being one of a production run of 269, is it worth a significant premium over over a WL now? R.M.
-
- Moderator
- Senior Member
- Posts: 8404
- Joined: Sat Nov 15, 2008 4:09 am
- Bikes: Multiple H-D, Ducati, BMW, Triumph, BSA,...
- Has thanked: 481 times
- Been thanked: 2954 times
Re: WLDD Surfaces
As far as I know the picture I posted (back cover of the Enthusiast in April '39) is the first public acknowledgement it exists. It is a WLD with added aluminum heads, the first time they appear on a 45 street bike. The cylinders are special in that the deep fins first appeared. The next season aluminum heads became standard on the WLD and the cylinders as well so the second D in the serial number was dropped as it no longer had special meaning. As far as value, it is only special if someone really likes having an odd number and then only if it is correct as far as the equipment goes.
Robbie
Robbie
-
- Senior Member
- Posts: 1500
- Joined: Tue Aug 03, 2010 7:10 pm
- Bikes: 1937 U big flathead, 88" stroker, dual port, big cams, pop-up pistons
- Location: Lynbrook, New York
- Has thanked: 32 times
- Been thanked: 387 times
- Contact:
Re: WLDD Surfaces
1939 is also the first use of the larger (UL-sized) 3 bolt manifold, front-drive magneto, and hotter roller tappet cam - whether they reached the WLDD on line, or just sold OTC, qien sabe?
-
- Junior Member
- Posts: 9
- Joined: Wed Mar 25, 2009 8:36 pm
- Bikes: Panhead 48F
Flathead 37U (at work) - Location: Germany
Re: WLDD Surfaces
More interested things about WLD, WLDR and WR´s :
http://www.beautyofspeed.com" onclick="window.open(this.href);return false;
Joe
http://www.beautyofspeed.com" onclick="window.open(this.href);return false;
Joe