It is 42* outside and I decided to start my bike. I checked the battery voltage and the plug gap. I started kicking to circulate oil through the engine. The cap to the oil tank popped off. I have an aftermarket horseshoe oil tank with a side fill spout welded in. A rubber ribbed cap plugs the fill spout.
I have used straight 70W oil since the 70's and don't recall the cap popping off when kicking the bike over. I was thinking the problem would solve itself when the bike runs and warms up a little. I have a spark but need to replace the gas to get it to run.
Any thoughts on why the cap would pop off? It does not sit in the spout tightly. Maybe the rubber is stiff.
Oil tank pressure
-
- Member
- Posts: 156
- Joined: Mon Nov 09, 2009 12:55 pm
- Bikes: 48 panhead
- Location: Riverside, IL
- Has thanked: 37 times
- Been thanked: 27 times
-
- Senior Member
- Posts: 1507
- Joined: Wed May 09, 2001 11:02 pm
- Bikes: 50 EL chopper
44 U that looks like a 37.
60 FLH (Sold)
59 FLH (Sold)
58 FL (Sold)
08 CVO Road King - Location: Maryland
- Has thanked: 244 times
- Been thanked: 138 times
Re: Oil tank pressure
Sounds like you have a belly full of oil. Don't attempt to top off the oil tank until you are able to run it and pump what's in the belly back to the tank. I hear from guys loosing those caps often. Would like to hear ingenious ways of securing them because I have one mounted on the top of my gas tank next to my gas cap and don't need it popping off and splattering me with hot oil.
-
- Senior Member
- Posts: 1433
- Joined: Thu Mar 26, 2020 5:46 pm
- Bikes: Rigid Panhead bobber, 68 Shovelhead, 2000 Road King Police bike, 2000 Dyna Wide Glide
- Location: Rhode Island
- Has thanked: 997 times
- Been thanked: 711 times
Re: Oil tank pressure
Cap doesn't fit tight enough. I have one of those side fill horseshoe oil tanks and the had that happen. My filler plug has a chrome cap on it with a threaded stud that fastened it to the rubber part. I found a pipe plug with an outside diameter that would slightly expand the rubber "stopper" when pushed into the stopper I.D. I drilled and tapped the blind end of the plug and threaded it onto the stud, using red Locktite. It's a bit stiffer to remove, but it's not going to ever pop out again. You can use anything of the right diameter that can stand up to the hot, oily conditions.
-
- Senior Member
- Posts: 1433
- Joined: Thu Mar 26, 2020 5:46 pm
- Bikes: Rigid Panhead bobber, 68 Shovelhead, 2000 Road King Police bike, 2000 Dyna Wide Glide
- Location: Rhode Island
- Has thanked: 997 times
- Been thanked: 711 times
Re: Oil tank pressure
Cap doesn't fit tight enough. I have one of those side fill horseshoe oil tanks and the had that happen. My filler plug has a chrome cap on it with a threaded stud that fastened it to the rubber part. I found a pipe plug with an outside diameter that would slightly expand the rubber "stopper" when pushed into the stopper I.D. I drilled and tapped the blind end of the plug and threaded it onto the stud, using red Locktite. It's a bit stiffer to remove, but it's not going to ever pop out again. You can use anything of the right diameter that can stand up to the hot, oily conditions.
-
- Senior Member
- Posts: 1433
- Joined: Thu Mar 26, 2020 5:46 pm
- Bikes: Rigid Panhead bobber, 68 Shovelhead, 2000 Road King Police bike, 2000 Dyna Wide Glide
- Location: Rhode Island
- Has thanked: 997 times
- Been thanked: 711 times
-
- Site Admin
- Senior Member
- Posts: 3291
- Joined: Mon Jan 01, 2001 12:00 pm
- Bikes: 1954 FL
- Location: Holland
- Has thanked: 108 times
- Been thanked: 488 times
-
- Member
- Posts: 156
- Joined: Mon Nov 09, 2009 12:55 pm
- Bikes: 48 panhead
- Location: Riverside, IL
- Has thanked: 37 times
- Been thanked: 27 times
Re: Oil tank pressure
PanPal wrote: ↑Wed Mar 29, 2023 11:21 pm Sounds like you have a belly full of oil. Don't attempt to top off the oil tank until you are able to run it and pump what's in the belly back to the tank. I hear from guys loosing those caps often. Would like to hear ingenious ways of securing them because I have one mounted on the top of my gas tank next to my gas cap and don't need it popping off and splattering me with hot oil.
Now I remember ... years ago I was riding and my cap fell off. I replaced it with the a newer ribbed cap. It fit more snug. Maybe it is time to buy a new cap.
Thanks for jogging my memory.