Can anyone positively identify this BT trans sprocket wrench?
Is it a 94660-25, or 94660-37, or something else?
No stamped part number, but it is genuine MoCo and fits 1-7/8" hex x 1" clearance hole for mainshaft and13 inches tip to tip.
Has one replacement handle, surviving original handle shows much usage (has had more hits than Elvis).
Edge as been chamfered/ground, probably to fit into L38-64 35159-39 oil deflector cup.
Has remnant nickel plating, which was common in 1920's and to me suggests 94660-25.
Any thoughts?
Nifty
Identity of factory tool
-
- Senior Member
- Posts: 536
- Joined: Wed Dec 14, 2011 7:04 am
- Bikes: 1948 Pan 61
1942 sv 74 x 4
1948 sv 74 x 1
1943 42U + sidecar with 6800 miles on the clock from new. - Location: South Africa
- Been thanked: 108 times
Re: Identity of factory tool
I have one of these ; mine appears to have been parkerized & full length is 16.5 inches.
Certainly mine fits all 40's , 50's & 60's Big twin c-shaft sprocket nuts ....
Certainly mine fits all 40's , 50's & 60's Big twin c-shaft sprocket nuts ....
-
- Senior Member
- Posts: 5327
- Joined: Tue Oct 31, 2017 1:00 pm
- Bikes: 1950 Panhead, Resto-Mod
1968 90", 5 Speed Shovelhead,
1984 Home Built Custom Evo 100" Bagger - Location: Knoxville, Tennessee
- Has thanked: 2801 times
- Been thanked: 2158 times
Re: Identity of factory tool
Funny thing is, regardless what the MoCo calls it, there is no sprocket on the countershaft, only on the main drive gearnifty wrote: ↑Tue Sep 06, 2022 12:42 am Can anyone positively identify this BT trans sprocket wrench?
Is it a 94660-25, or 94660-37, or something else?
No stamped part number, but it is genuine MoCo and fits 1-7/8" hex x 1" clearance hole for mainshaft and13 inches tip to tip.
Has one replacement handle, surviving original handle shows much usage (has had more hits than Elvis).
Edge as been chamfered/ground, probably to fit into L38-64 35159-39 oil deflector cup.
Has remnant nickel plating, which was common in 1920's and to me suggests 94660-25.
Any thoughts?
Nifty
94660-25 trans sprock wrench.jpg
94660-37 trans sprock wrench.jpg
trans sprock wrench a.JPG
trans sprock wrench b.JPG
trans sprock wrench c.JPG
trans sprock wrench d 13 inch.JPG
The countershaft, more correctly called a layshaft, is buried deep within the transmission.....
-
- Moderator
- Senior Member
- Posts: 8378
- Joined: Sat Nov 15, 2008 4:09 am
- Bikes: Multiple H-D, Ducati, BMW, Triumph, BSA,...
- Has thanked: 478 times
- Been thanked: 2933 times
Re: Identity of factory tool
There is a third version as well which uses the same part number, with an extended shaft allowing the handle to be outboard of the transmission shaft and making it easier to use. There is one in this pictureon the left in Cad plate. In the '35 catalog it does not yet have a year suffix, just an "X" as most accessories and tools did, and says it fits back to '16. I'll look in earlier and later catalogs for more info.
- Attachments
-
- DCP_4336.JPG (161.3 KiB) Viewed 682 times
-
- Senior Member
- Posts: 591
- Joined: Wed Apr 29, 2020 8:24 am
- Bikes: 68 FL
- Location: Nambour Qld Australia
- Has thanked: 256 times
- Been thanked: 476 times
Re: Identity of factory tool
Roodog
The terminology stems from pre WW1 and the invention of what was known as the 2 shaft or, in the parlance of the day, the "counter-shaft gearbox/transmission". Which, initially as a generally 3 speed device, was a revolutionary improvement, compared to the preceding direct belt drive and fragile 2, or 3 speed epicyclic transmissions built into rear wheel hubs.
People are lazy and language is constantly evolving, hence abbreviation to "countershaft sprocket" because it was attached to/associated with the "counter-shaft gearbox/transmission". Single gear race bikes use single shaft "countershafts" to obtain desired overall ratio, with acceptable sprocket sizes. To call these "mainshafts" would to some, perhaps, be more technically correct, but crazy due to long established, real world usage.
As to the correctness of countershaft, or layshaft, both words are "correct" the countershaft "lays" alongside and "counter to" the mainshaft. In some places, layshaft is a very common automotive term and what I was trained with. However we are MoCo product enthusiasts, sharing a MoCo product forum with many who struggle with the "English" language and layshaft is not a term used by the MoCo. So IMHO, the best path is for all to use MoCo language. "Singing from the same song sheet". We are also all human, some lazier than others, set in our ways etc, so we also cut each other a little slack.
Nifty
-
- Senior Member
- Posts: 5327
- Joined: Tue Oct 31, 2017 1:00 pm
- Bikes: 1950 Panhead, Resto-Mod
1968 90", 5 Speed Shovelhead,
1984 Home Built Custom Evo 100" Bagger - Location: Knoxville, Tennessee
- Has thanked: 2801 times
- Been thanked: 2158 times
Re: Identity of factory tool
Bla, Bla, Bla. Nifty....
The counter shaft on a Harley Big Twin does not have a sprocket, period.
BUT, some motorcycles do have a CS sprocket, some of our readers don't know which end of a hammer is metric, so let's not confuse the issue just for the sake of laziness.
I keep it simple, and refer to said sprocket as the Transmission Sprocket, and let the chips fall where they may....
....RooDog....
The counter shaft on a Harley Big Twin does not have a sprocket, period.
BUT, some motorcycles do have a CS sprocket, some of our readers don't know which end of a hammer is metric, so let's not confuse the issue just for the sake of laziness.
I keep it simple, and refer to said sprocket as the Transmission Sprocket, and let the chips fall where they may....
....RooDog....
Last edited by RooDog on Sat Sep 17, 2022 1:30 pm, edited 1 time in total.
-
- Member
- Posts: 203
- Joined: Thu May 26, 2022 5:10 am
- Bikes: 2001 fxst 68 shovel
- Location: Victoria
- Has thanked: 301 times
- Been thanked: 83 times
Re: Identity of factory tool
That is FN Funny RooRooDog wrote: ↑Wed Sep 07, 2022 12:48 am Bla, Bla, Bla. Nifty....
The counter shaft on a Harley Big Twin does not have a sprocket, period.
BUT, some motorcycles do have a CS sprocket, some of our reader don't know which end of a hammer is metric, so let's not confuse the issue just for the sake of laziness.
I keep it simple, and refer to said sprocket as the Transmission Sprocket, and let the chips fall where they may....
....RooDog....