Air Cleaner Bracket 1967 Early Shovel

[hdmarkus]

Hi,

I’m searching for this part 29027-66 ? It’s hard to find in Germany so my question is, does anyone have the measurements for this? If yes, I could make it by myself.

Thanks
Markus

[panheadrider1961]

cant get the link....... custom motorcycle parts u, k,on ebay 13 lbs money oem says has alot of them and free post hope this helps

[panheadrider1961]

https://www.ebay.co.uk/itm/353042532050 ... SwYY1ejyKz

[hdmarkus]

Thanks I also found that on eBay but there is no shipping to Germany Nevertheless I asked if it’s possible to send me the item. I’m still waiting for reply. Thanks Markus

[RooDog]

Unless you are going for a 100 point restoration, I would make my own, maybe using stainless steel and either polishing it, or bead blasting it for an OEM like finish. By the time import fees are added to the nominal selling price, + postage, a home made item starts to look pretty inviting, ja?
....RooDog....

[panheadrider1961]

jan william boone has it i guess still on inventory page about 40 euro with all that tav b.s. or whatever you have to pay called

[panheadrider1961]

if image you are posting is almost to scale looks like 1/8 or 3/16 bar stock,12 inches overall and 7/8 wide, bend on left 35 degrees on what i measure 1 3/4 inches with 3/8 hole center line at 1 inch ,6 1/4 inch mid section to right bend point 28 to 30 degrees 3 inches with 3/8 hole center line 1 inch sorry don,t have metric tape within reach hope i am close maybe someone has one to get exact hope this helps, U. S. money for this project 1.50 plus 45 minutes labor propane torch ,table vise ,crescent wrench, 3/8 drill bit and drill motor bench top or hand held grinder to make reliefs on ends and some rattle can black spray paint

[hdmarkus]

jan william boone has it i guess still on inventory page about 40 euro with all that tav b.s. or whatever you have to pay called

Yes he has, but the minimum order is 125€ and minimum package weight is 500gr

[hdmarkus]

Unless you are going for a 100 point restoration, I would make my own, maybe using stainless steel and either polishing it, or bead blasting it for an OEM like finish. By the time import fees are added to the nominal selling price, + postage, a home made item starts to look pretty inviting, ja?
....RooDog....

if image you are posting is almost to scale looks like 1/8 or 3/16 bar stock,12 inches overall and 7/8 wide, bend on left 35 degrees on what i measure 1 3/4 inches with 3/8 hole center line at 1 inch ,6 1/4 inch mid section to right bend point 28 to 30 degrees 3 inches with 3/8 hole center line 1 inch sorry don,t have metric tape within reach hope i am close maybe someone has one to get exact hope this helps, U. S. money for this project 1.50 plus 45 minutes labor propane torch ,table vise ,crescent wrench, 3/8 drill bit and drill motor bench top or hand held grinder to make reliefs on ends and some rattle can black spray paint

You both are right, I will make a homemade version :D

[George Greer]

jan william boone has it i guess still on inventory page about 40 euro with all that tav b.s. or whatever you have to pay called

Yes he has, but the minimum order is 125€ and minimum package weight is 500gr

That is one of the reasons after many years of doing business JW BOON, that I quit doing business with them.

1st he quit mailing to the USA.
2 For a long time he had a 80 euro limit

Now, raised the minimum limit so high, and minimum weight for mailing, I will probably never shop with them again.

To me that’s not a smart way to run a business.

My 2 cents,

Now back to regular broadcasts.

George

[hdmarkus]

Here is the homemade version

[FL54]

As they say, “necessity is the mother of invention.” Nicely done.