Wrist Pin Fit to Piston
Press or sliding fit?
-
- Senior Member
- Posts: 1433
- Joined: Thu Mar 26, 2020 5:46 pm
- Bikes: Rigid Panhead bobber, 68 Shovelhead, 2000 Road King Police bike, 2000 Dyna Wide Glide
- Location: Rhode Island
- Has thanked: 997 times
- Been thanked: 711 times
Wrist Pin Fit to Piston
When I installed new pistons in my motor they were a tight fit. I don't like whacking on anything attached to my connecting rods with a mallet, so I pressed the pins through using a threaded rod with nuts, washers and a socket.This was done with all parts at ambient temperature. Heating the pistons or chilling the pins might have made a difference. I've had tight pins before and I've also had them slide right in. I always assumed that as long as the pin fit to the rod bushing was correct it shouldn't matter. Last night I was killing some time and watched a video of a pan rebuild by Tattro Machine. Tattro took a lot of time honing the piston pin bosses until he got a sliding fit. Holding the piston with the pin axis vertical, and with lubrication, the pins slowly slid down through the pistons. I don't have a Sunnen power hone, and I suspect most people without fully outfitted shops don't either. I've installed pistons on many different bikes more times than I can remember and never had any issues. Is this critical or more a matter of preference?
Thanks
Jim
Thanks
Jim
-
- Senior Member
- Posts: 5327
- Joined: Tue Oct 31, 2017 1:00 pm
- Bikes: 1950 Panhead, Resto-Mod
1968 90", 5 Speed Shovelhead,
1984 Home Built Custom Evo 100" Bagger - Location: Knoxville, Tennessee
- Has thanked: 2801 times
- Been thanked: 2159 times
Re: Wrist Pin Fit to Piston
That was a good thought from Tatro, Jim. I have had issues with zero clearanced parts from time to time. Slipping together, and at other times needing just a little persuasion. I wouldn't have any qualms using a hand held hone on a piston as long as the rod to pin fit was OK. Just enough working the piston to get the pin through by hand pressure, and nothing more. And of course, lubrication is mandatory.....
Or how about a hair drier/heat gun on the slugs?
....RooDog....
Or how about a hair drier/heat gun on the slugs?
....RooDog....
-
- Senior Member
- Posts: 1433
- Joined: Thu Mar 26, 2020 5:46 pm
- Bikes: Rigid Panhead bobber, 68 Shovelhead, 2000 Road King Police bike, 2000 Dyna Wide Glide
- Location: Rhode Island
- Has thanked: 997 times
- Been thanked: 711 times
Re: Wrist Pin Fit to Piston
Can you give me an example of a hand-held hone?RooDog wrote: ↑Wed Oct 13, 2021 6:08 pm That was a good thought from Tatro, Jim. I have had issues with zero clearanced parts from time to time. Slipping together, and at other times needing just a little persuasion. I wouldn't have any qualms using a hand held hone on a piston as long as the rod to pin fit was OK. Just enough working the piston to get the pin through by hand pressure, and nothing more. And of course, lubrication is mandatory.....
Or how about a hair drier/heat gun on the slugs?
....RooDog....
Thanks
Jim
-
- Site sponsor
- Senior Member
- Posts: 1921
- Joined: Fri Jul 01, 2011 8:43 pm
- Bikes: 1969 FLF
1937 EL
1940 U - Location: san diego
- Has thanked: 1478 times
- Been thanked: 244 times
Re: Wrist Pin Fit to Piston
they look like this..............
- Attachments
-
- 911-655_A_V1.jpg (13.22 KiB) Viewed 537 times
-
- Senior Member
- Posts: 5327
- Joined: Tue Oct 31, 2017 1:00 pm
- Bikes: 1950 Panhead, Resto-Mod
1968 90", 5 Speed Shovelhead,
1984 Home Built Custom Evo 100" Bagger - Location: Knoxville, Tennessee
- Has thanked: 2801 times
- Been thanked: 2159 times
-
- Moderator
- Senior Member
- Posts: 8411
- Joined: Sat Nov 15, 2008 4:09 am
- Bikes: Multiple H-D, Ducati, BMW, Triumph, BSA,...
- Has thanked: 483 times
- Been thanked: 2958 times
Re: Wrist Pin Fit to Piston
Factory specs were always light press fit with pistons warmed up with a heat gun or propane torch. The pin is intended to rock with the piston and only move on the pin bushing.
-
- Senior Member
- Posts: 591
- Joined: Wed Apr 29, 2020 8:24 am
- Bikes: 68 FL
- Location: Nambour Qld Australia
- Has thanked: 256 times
- Been thanked: 477 times
Re: Wrist Pin Fit to Piston
I second Rubone,
IMO For normal street use the stock set-up, assembled with heat, ensures quieter operation in running engine. Heat guns are great!
Be aware that hone-fitted aluminum pistons and bronze bushings quickly loosen when the microscopic ridges quickly flatten down in use.
Can be mitigated with ultra fine stones and "diamond" laps.
IMO Same applies to bottom end & trans, a fine line-lapped finish in races and polished shafts won't loosen up as much as a Sunnen honed finish and straight out of the box ground shafts & crankpins.
Laborious vs fast.
Nifty
IMO For normal street use the stock set-up, assembled with heat, ensures quieter operation in running engine. Heat guns are great!
Be aware that hone-fitted aluminum pistons and bronze bushings quickly loosen when the microscopic ridges quickly flatten down in use.
Can be mitigated with ultra fine stones and "diamond" laps.
IMO Same applies to bottom end & trans, a fine line-lapped finish in races and polished shafts won't loosen up as much as a Sunnen honed finish and straight out of the box ground shafts & crankpins.
Laborious vs fast.
Nifty
-
- Senior Member
- Posts: 1433
- Joined: Thu Mar 26, 2020 5:46 pm
- Bikes: Rigid Panhead bobber, 68 Shovelhead, 2000 Road King Police bike, 2000 Dyna Wide Glide
- Location: Rhode Island
- Has thanked: 997 times
- Been thanked: 711 times
Re: Wrist Pin Fit to Piston
That might be a little extreme for the amount of clearance I'm talking about. I was actually wondering if somebody makes something like an adjustable reamer, but with expanding honing stones instead of blades.
-
- Senior Member
- Posts: 1433
- Joined: Thu Mar 26, 2020 5:46 pm
- Bikes: Rigid Panhead bobber, 68 Shovelhead, 2000 Road King Police bike, 2000 Dyna Wide Glide
- Location: Rhode Island
- Has thanked: 997 times
- Been thanked: 711 times
-
- Senior Member
- Posts: 1433
- Joined: Thu Mar 26, 2020 5:46 pm
- Bikes: Rigid Panhead bobber, 68 Shovelhead, 2000 Road King Police bike, 2000 Dyna Wide Glide
- Location: Rhode Island
- Has thanked: 997 times
- Been thanked: 711 times
Re: Wrist Pin Fit to Piston
I appreciate the link, but it comes up in French, which I don't know how to read or speak. I tried Google Translate, but nothing happened.panhead51 wrote: ↑Thu Oct 14, 2021 11:00 am Here is my method.
http://panhead51.eklablog.com/montage-d ... -c30936008
-
- Member
- Posts: 115
- Joined: Tue Sep 25, 2012 7:45 am
- Bikes: panhead 51 fl
- Location: Burgundy
- Has thanked: 1 time
- Been thanked: 7 times
- Contact:
Re: Wrist Pin Fit to Piston
It's simple.
Once the tool has been inserted into the piston, make 2, three passes and you're done.
Once the tool has been inserted into the piston, make 2, three passes and you're done.
-
- Senior Member
- Posts: 1433
- Joined: Thu Mar 26, 2020 5:46 pm
- Bikes: Rigid Panhead bobber, 68 Shovelhead, 2000 Road King Police bike, 2000 Dyna Wide Glide
- Location: Rhode Island
- Has thanked: 997 times
- Been thanked: 711 times
Re: Wrist Pin Fit to Piston
I've actually done this for a lot of different things. Just haven't put too much thought into this since the consensus seems to be that it's okay for to have a press fit into the piston.
-
- Senior Member
- Posts: 5327
- Joined: Tue Oct 31, 2017 1:00 pm
- Bikes: 1950 Panhead, Resto-Mod
1968 90", 5 Speed Shovelhead,
1984 Home Built Custom Evo 100" Bagger - Location: Knoxville, Tennessee
- Has thanked: 2801 times
- Been thanked: 2159 times
Re: Wrist Pin Fit to Piston
to all....
We are dealing with ambient room temp, about 70*, at assembly time, a running engine's parts are at quite a bit higher temp, and all the running clearances are quite different than when cold. We all know this. And surely the piston to pin fit loosens up or else there would be no need for the keepers at both ends of the pin, no? Many automotive piston run without keepers. The small end of the rod is heated and the pin presses in and is locked to the rods by a friction & shrink fit. Harleys', on the other hand, are full floating with running clearance at three points and with keepers on both ends. Forget to install, or lose a keeper, and see how that turns out.... Not too good....
Yes there are ways to enlarge the pistons' bore, but are probably not a good idea, reputable manufactures generally know what they are doing if they sell a "pin fitted" piston kit. But not a bad practice to double check clearances and fit of new parts
....RooDog....
We are dealing with ambient room temp, about 70*, at assembly time, a running engine's parts are at quite a bit higher temp, and all the running clearances are quite different than when cold. We all know this. And surely the piston to pin fit loosens up or else there would be no need for the keepers at both ends of the pin, no? Many automotive piston run without keepers. The small end of the rod is heated and the pin presses in and is locked to the rods by a friction & shrink fit. Harleys', on the other hand, are full floating with running clearance at three points and with keepers on both ends. Forget to install, or lose a keeper, and see how that turns out.... Not too good....
Yes there are ways to enlarge the pistons' bore, but are probably not a good idea, reputable manufactures generally know what they are doing if they sell a "pin fitted" piston kit. But not a bad practice to double check clearances and fit of new parts
....RooDog....