I got this from a friend of mine and i wonder if it is okay to install it on the Pan? There is no +/- marking on it only 2 connections. If you want to a can post a picture. No install tec on the accel home page either.
//HM
Accel coil number:140403
-
- Member
- Posts: 72
- Joined: Fri Apr 08, 2005 4:29 pm
- Bikes: Hydra-glide 1953. Built to a 1948 .
- Location: Sweden
- Has thanked: 5 times
-
- Senior Member
- Posts: 2407
- Joined: Wed Jul 07, 2010 4:28 am
- Bikes: 1950Panhead
- Location: USA
- Has thanked: 1 time
- Been thanked: 366 times
Re: Accel coil number:140403
Does this coil have a metal core through the center and mount holes on both ends?
If so it is a 12 volt coil for CB750 and Kaw Z1 and not suitable for panheads.
48-64 Panheads came from factory with six volts systems.
Find another coil.
Jerry
If so it is a 12 volt coil for CB750 and Kaw Z1 and not suitable for panheads.
48-64 Panheads came from factory with six volts systems.
Find another coil.
Jerry
-
- Senior Member
- Posts: 2682
- Joined: Sat May 29, 2004 8:21 am
- Bikes: '31 VL, '34 VD, '45 WLA, '47 WL, '49 FL, '51 WL, '58 ST (Hummer), '71 GE (Servi)
- Location: Lonoke, Arkansas
- Has thanked: 5 times
- Been thanked: 49 times
Re: Accel coil number:140403
harleyman,
If you are running 12 volts & points that coil will work. It will NOT work with a 6 volt system or a 12 volt system that has a capcitive discharge ignition system. And it does not matter which terminal is connected positive or negative; from the prestolite/Accel instructions;
"Attach primary leads from the ignition switch and ignition
pick-up to either of the brass lead studs. These can be
installed to either stud without negatively affecting the system."
But I would suggest exactly what Jerry did; find a different coil.
jmho
mike
If you are running 12 volts & points that coil will work. It will NOT work with a 6 volt system or a 12 volt system that has a capcitive discharge ignition system. And it does not matter which terminal is connected positive or negative; from the prestolite/Accel instructions;
"Attach primary leads from the ignition switch and ignition
pick-up to either of the brass lead studs. These can be
installed to either stud without negatively affecting the system."
But I would suggest exactly what Jerry did; find a different coil.
jmho
mike
- Attachments
-
- Accel 140403
- 140403KS.jpg (77.33 KiB) Viewed 1579 times
-
- Member
- Posts: 72
- Joined: Fri Apr 08, 2005 4:29 pm
- Bikes: Hydra-glide 1953. Built to a 1948 .
- Location: Sweden
- Has thanked: 5 times
Re: Accel coil number:140403
I do have single point 12 volt system and sinse i´ve had some pretty hard to find problems with the bike not wanting to idle (if you read my old posts) and die after a few short sec i was thinking of trying this one out, just as a test!
I am not suicidle..
I am not suicidle..
-
- Inactive member
- Member
- Posts: 10
- Joined: Thu Jan 19, 2012 11:54 pm
- Bikes: 06 FXDB 04 FLHTCUI 89FLHTCU
Re: Accel coil number:140403
Have you changed the condencer???HARLEYMAN53 wrote:I do have single point 12 volt system and sinse i´ve had some pretty hard to find problems with the bike not wanting to idle (if you read my old posts) and die after a few short sec i was thinking of trying this one out, just as a test!
I am not suicidle..
-
- Member
- Posts: 72
- Joined: Fri Apr 08, 2005 4:29 pm
- Bikes: Hydra-glide 1953. Built to a 1948 .
- Location: Sweden
- Has thanked: 5 times