:: Panhead and Flathead site ::
Knowledge Base (Forum Archive)
  General(639) Carburetor Carburetor and Fuel System(349)
- Linkert (212)
- S&S (65)
Electrical System Electrical System (528)
- Generator
Transmission Transmission, Clutch, Belt and Chain (33)
- Transmission, Starter & Shifting (436)
- Clutch & Mousetrap (251)
- Chains & Belts (109)
- Sprockets (61)
  Troubleshooting (123) Chassis and Frame Chassis & Frame (13)
- Fenders, Primary, Tanks & Paint (429)
- Frame & Fittings (300)
- Handlebars & Cables (112)
- Seat (118)
- Speedometer, Dashboard & Instruments (112)
Forks Forks and Shocks (232) Accessoires Accessories (154)
Identification Identification (71)
- VIN / Cases / Heads (61)
- Frame / Transmission (82)
Wheels and Tires Wheels & Tires (210) Ignition Ignition and timing (386)
Brakes Brakes (181) Exhaust Exhaust System (125) Motor

Motor (156)
- Bottom End, Crankcases (276)
- Top End, Cylinders (393)
- Cylinderheads (296)
- Gear Case, Cams (156)
- Lubrication System (425)

 
Specific Motor categories:
Bottom End (cases and crankshaft)
Top End (cylinders, pushrods etc.)
Cylinderheads
Gear Case (cams, idlers, cam cover)
Lubrication System (oil feed pump and scavenger pump, reservoir, filter, and lines)
Gear Case (cams, idlers, cam cover): 171 topics
'63 Pan timing cover leak
'63-'64 outside oiler cases for a '65
1940 Cam Cover
1940 Cam Cover
1954 cam gear case & cover gasket
1955 Panhead Cam Cover
1955 Panhead victory cam
1959 breather gear
1959 FLH idler gear & circuit breaker gear slop
1963 cam cover repair
1963 timing cover oil leak
25279-36 Separator, Breather screen
25300-36 breather valve and gear
412 sifton
54 cam cover
54 Panhead
57 & older inner cam bushing/ bearing question
61 inchers cam in 74
61" cam in an FL?
64 Cam Cover on 65 Panhead
64 pan idler gear shaft removal
65 panhead main drive gear
65 shovelhead engine how many timing gears does it have?
A welded inner cam bearing seat.
Andrews 'F.' grind cam for Pan
Andrews A cam with 10:1 pistons
Andrews AB Cam
Andrews cams
Andrews F grind cam...
Andrews J cam ID?
Andrews specs vs Harley factory manual specs
another cam question
Best available cam for a 74"
Breather Gear questions?
Cam
Cam / gear cover
Cam / valve train recommendation
CAM & PINION GEAR
cam and cam chest gear assembly i.d.
Cam bearing question
Cam blew right case?
Cam bushing
cam bushing reamer
Cam bushing reamer
Cam change
Cam chest gear needs w/an Alternator left case!
CAM CHEST REBUILD
Cam choice +
Cam cover
Cam cover ??
cam cover cam bushing reamer
Cam cover holes too big
Cam cover question
Cam Cover: early (1948) onto a 55 FL motor.
Cam covers?
Cam Duration
cam gear fell out
Cam ID
Cam identification
Cam identification
Cam learning experience
Cam problem?
Cam question
CAM QUESTION
Cam Question
Cam recommendations
Cam recommendations?
Cam selection??
Cam shaft end play
cam shafts ?
Cam Spec. Questions
Cam Specs
Cam thrust washer
Cam vs. carb
camgear and timing question
Cams
Cams
Cams with allround performance
cams, sifton or crane?
Camshaft Condition
CAMSHAFTS-?
Can anyone ID this camshaft?
Changing a Cam gear
circuit breaker drive gear
Clearance between exaust lobe and timer gear.
Correct 51 cam cover(s)
Correct Cam Selection for "No Ping" Operation?
cracks at cam bushing
Cracks between cam journal and mainshaft journal in case
Crane 296A cam
Crane cam
EARLY PAN REAMERS
Engine cases
Factory cam specs/ cam suggestions.
FLH cam
FLH Cam
Gear Case Cover Removal and Installation
Gear Mesh Problem?
Gear Timing Marks
gearcase cover bushing
generator drive gear
generator gear lash...how much is too much?
Generator Idler Gear Stud to Cam Cover 'Hole' Clearance
Glass beads in gearcase - new problem
H grind cam
Hairline cracks in case from cam bushing
Happy with H cam
Hollow bolt washer
how to ream a idler gear bushing
Identify my cam
idler and intermediate gear shaft screws.
idler gear
Idler gear backlash
Idler gear bushing installation
Idler gear identification
idler shafts
Inner cam bearing damaged
Inner cam bearing spun and cracked
Interesting camshaft binding problem
interesting etching inside panhead gearcase
Is this a "Knuckle" ~Lightning~ Cam ?
J grind cam vs single point timer
Leaking oil from generator mount bolt
leineweber cams
Leineweber cams
main drive gear seal removal help
Modifying a 64 Pan Cam Cover to suit a 73 Shovel
Name that cam?
NEED NEW CAM??
Need to ID my cam
New Cam
number of teeth on pinion and generator gears
Pan cam identification
Panhead Cam Cover
Panhead cam questions
panhead cam selection
Pinion bushing seating depth
Pinion gear
Pinion gear removal
Pinion gear sizes
Pros & cons hydraulic vs. solid tappets
remove breather gear screen?
removing gearcase cover.
Removing my cam/gear cover
Replacing Andrews "B" cam with the S&S 514
reverse crankcase gears in a panhead
Rivera cams
side cover r&r question
Sifton 468S cam
Sifton and Andrews cams - advice
Sifton cam data for big twins 1936-*
Sifton Solids
Sifton's cam grinds being re-produced by Black Widow in Colo
spun cam bearing
stuck breather gear help
The camshaft is out...
The roller on a lifter grenaded on my way up to speed
Thrust washer
Timer and idler gear backlash
timing cover dowel pin question
Timing gear spacers
Timing gears
Timing gears question
Timing your cam, how?
Torque for Cam cover
Torque Setting - Cam Chest Screws
Victory Cam
Victory Cam (H cam)
Victory Camshaft
What is the correct cam cover for a 1953 FL ?
Would you Chrome the Cam Cover?
Copyright © 2001-2023 Panhead/PTH