Description: What media have you guys used to get the cast surface look.
had to fix a few cracks in the case, got that done.
but what media have you guys used to get the cast surface look.
I have tryed a few things and the surface still has the smooth look from the repair.
was thinking I might try steel shot, like the kind that is used in shot peening. not going to blast it hard, just give it that as cast look.
anybody have the answer?
mbskeam
Case finish after welding
-
- Senior Member
- Posts: 6938
- Joined: Sun Feb 10, 2002 2:30 am
- Bikes: -
- Location: Central Illinois
- Has thanked: 112 times
- Been thanked: 310 times
Re: Case finish after welding
I use steel shot, before other finish preps.
Don't forget a marred-up coarse grinding wheel on a piece o' poolcue for that extra realism (genuine old outlaw trick).
....Cotten
Don't forget a marred-up coarse grinding wheel on a piece o' poolcue for that extra realism (genuine old outlaw trick).
....Cotten
-
- Senior Member
- Posts: 1014
- Joined: Fri Apr 18, 2003 12:26 pm
- Bikes: *
- Location: Sultan, WASH
- Been thanked: 6 times
- Contact:
Re: Case finish after welding
what size?
"Don't forget a marred-up coarse grinding wheel on a piece o' poolcue for that extra realism (genuine old outlaw trick)."
????
okay, what are you talking about. I cant seem to wrap my head into this one........
mbskeam
"Don't forget a marred-up coarse grinding wheel on a piece o' poolcue for that extra realism (genuine old outlaw trick)."
????
okay, what are you talking about. I cant seem to wrap my head into this one........
mbskeam
-
- Senior Member
- Posts: 1507
- Joined: Wed May 09, 2001 11:02 pm
- Bikes: 50 EL chopper
44 U that looks like a 37.
60 FLH (Sold)
59 FLH (Sold)
58 FL (Sold)
08 CVO Road King - Location: Maryland
- Has thanked: 245 times
- Been thanked: 138 times
Re: Case finish after welding
I was told to use coarse sand paper and tap on the back with a hammer. I didn't try it because mine was a fin on my head I made and welded on, but it sounded like a decent idea.
-
- Senior Member
- Posts: 6938
- Joined: Sun Feb 10, 2002 2:30 am
- Bikes: -
- Location: Central Illinois
- Has thanked: 112 times
- Been thanked: 310 times
Re: Case finish after welding
I can't remember the 'gauge' of the shot, but they average ~.020"; coulda been a little coarser...
The broken stone is for beating 'character' into the fresh metal, using irregular random strokes while scolding "Bad motorcycle, Bad!"
Once you have employed this technique, you learn to recognize where boogered VIN numbers have been fudged with it.
...Cotten
The broken stone is for beating 'character' into the fresh metal, using irregular random strokes while scolding "Bad motorcycle, Bad!"
Once you have employed this technique, you learn to recognize where boogered VIN numbers have been fudged with it.
...Cotten
-
- Senior Member
- Posts: 2096
- Joined: Fri May 24, 2002 1:00 am
- Bikes: 64FL 99FLHR 01FXSTD
- Location: Mpls. MN.
- Has thanked: 71 times
- Been thanked: 149 times
Re: Case finish after welding
After I got my cases back from Head Hog there were several areas that looked freshly ground {shiney} My engine assembly guy glass beaded the cases so now you cant tell they were ever touched.