need help tracing my wiring routes.

Electrical issues
Forum rules
Please start new topics here: New Panhead and Flathead topics
Post Reply
neilw
Member
Posts: 352
Joined: Sat Dec 20, 2008 3:24 am
Bikes: 1995 Roadking(still brand new)
1991 HD springer
1959 pan (I'm reassembling)
1991 BMW 75RT.
Location: Calgary
Has thanked: 91 times
Been thanked: 18 times

need help tracing my wiring routes.

#1

Post by neilw »

I'm attaching a photo of Harleys wiring diagram for a 59 FLH . Can some one help me with the exact route the circuit breaker to coil wire goes ( does it pass between the cylinders)?Also loom "L" gen.to vlt.reg.
Loom "C" and loom"A" have a lot of wires comming into the instrument panel base plate area .Some wires mount on the top of the base plate ,others go below to connections .Since my base plate has 3 holes with nothing to go in them I'm wondering if some of the wiring comes up through these holes ,or do they just come in the rear of the base plate over the top of it.
Also loom "N" from the oil sending switch to the light ,I'm not sure where that runs either.
Thanks ,Neil
Attachments
wiring page 001 (Large).jpg
wiring page 001 (Large).jpg (88.19 KiB) Viewed 590 times
john HD
Moderator
Senior Member
Posts: 3711
Joined: Mon Dec 01, 2003 11:38 pm
Bikes: '42 WLA X 2, '55FL, '93 Ultra Classic, '91 Fatboy, '97 883, '03 Rokon Trailbreaker, '83 GPz 750.
Has thanked: 70 times
Been thanked: 128 times

Re: need help tracing my wiring routes.

#2

Post by john HD »

neil

yes the 3 looms go through the holes in the speedo plate. i believe dave swanson just posted a very good pic of his '56.

the timer wires run down the seat post to the right side of the motor behind the pushrods. there is a clip on the top rear case bolt. (with a clip on the seat tube with loom "n")

the gen/reg wires run down the left front frame down tube with two clips and go to the gen and on to regulator.

loom n as you call it goes from the junction box behind the coil down the seat post tube to the oil sender and stop switch. this is held in place with a clip on the seat tube with the timer wire.

john
mbskeam
Senior Member
Posts: 1014
Joined: Fri Apr 18, 2003 12:26 pm
Bikes: *
Location: Sultan, WASH
Been thanked: 6 times
Contact:

Re: need help tracing my wiring routes.

#3

Post by mbskeam »

DSC_0349.jpg
DSC_0349.jpg (76.73 KiB) Viewed 466 times
DSC_0358.jpg
DSC_0358.jpg (77.38 KiB) Viewed 466 times
DSC_0360.jpg
DSC_0360.jpg (72.73 KiB) Viewed 466 times
view of box under coil top side
DSC_0361.jpg
DSC_0361.jpg (69.17 KiB) Viewed 466 times
loom under tank and top of rear pan cover
DSC_0362.jpg
DSC_0362.jpg (67.27 KiB) Viewed 466 times
DSC_0363.jpg
DSC_0363.jpg (56.95 KiB) Viewed 466 times
DSC_0364.jpg
DSC_0364.jpg (78.66 KiB) Viewed 466 times
neilw
Member
Posts: 352
Joined: Sat Dec 20, 2008 3:24 am
Bikes: 1995 Roadking(still brand new)
1991 HD springer
1959 pan (I'm reassembling)
1991 BMW 75RT.
Location: Calgary
Has thanked: 91 times
Been thanked: 18 times

Re: need help tracing my wiring routes.

#4

Post by neilw »

Thanks loads you guys.
Neil
Post Reply

Return to “Electrical”