rear cross over ..how long?
-
- Member
- Posts: 16
- Joined: Fri May 10, 2013 3:32 pm
- Bikes: 52 pan
- Location: northern, new jersey
rear cross over ..how long?
hey guys, i just got a 52 frame and the cross over was cut down in size..can someone please help..can you go out to your garage and measure how long that outside pipe shaft is from end to end, and from the right side to the center of the grease fitting....this is my first post.please help...and carfull ridin...thankx to all...
-
- Senior Member
- Posts: 2405
- Joined: Wed Jul 07, 2010 4:28 am
- Bikes: 1950Panhead
- Location: USA
- Has thanked: 1 time
- Been thanked: 366 times
-
- Member
- Posts: 16
- Joined: Fri May 10, 2013 3:32 pm
- Bikes: 52 pan
- Location: northern, new jersey
-
- Member
- Posts: 16
- Joined: Fri May 10, 2013 3:32 pm
- Bikes: 52 pan
- Location: northern, new jersey
Re: rear cross over ..how long?
so just the pipe it-self is 8 1/2 " with no shaft in it ...correct?.. i still need to know how far in on center is the grease fitting?... i do thank any and all responses........ride,,wrench,,repete...
-
- Former member
- Senior Member
- Posts: 2789
- Joined: Tue Dec 18, 2007 2:10 pm
- Bikes: 1941/59 EL
1952 FL
1977 FLH
1994 Fatboy - Has thanked: 22 times
- Been thanked: 110 times
Re: rear cross over ..how long?
My '52 frame also measures 8-1/2" end to end with the crossover shaft removed.
I get 2-11/16" from the right side, inboard to the center of the grease zerk hole.
I get 2-11/16" from the right side, inboard to the center of the grease zerk hole.
-
- Member
- Posts: 16
- Joined: Fri May 10, 2013 3:32 pm
- Bikes: 52 pan
- Location: northern, new jersey
-
- Former member
- Senior Member
- Posts: 3336
- Joined: Sat Jun 26, 2010 1:54 pm
- Bikes: 1958flh 1969sporty,had a knuckle but sold back to original owner
- Location: NEW JERSEY
- Has thanked: 195 times
- Been thanked: 278 times
Re: rear cross over ..how long?
52-Gonzo!---Make sure when shaft is installed it has no SIDE to side play!--You will find that the pedal side & rod going to rearbrake Have side pull on them!--This is where they wear-out!--Put bushings in if play is .020 or more!,-& usualy its more!---Also do not over grease the shaft!--If installing -you already have it greased by hand!--So Check on it from time to time-& you will see the crud build-up on both ends!--Wipe Clean & usually 1 to 2-pumps is all that nessesary!.---Respectfully---RICHIE
-
- Member
- Posts: 16
- Joined: Fri May 10, 2013 3:32 pm
- Bikes: 52 pan
- Location: northern, new jersey
Re: rear cross over ..how long?
hey richie, thanx...that will help alot....i realy do want anybodys in-put on the rear brake ...my buddy ownes a antique bike shop in town and is puttin together all the parts that i need, .with out his help i'd be skrewed..also i am looking for blue prints on the 52 wishbone frame...the one for sale on ebay are very hard to read, { blurry}.. and there were some in a chopper book, but those don't have measurement's for floorboard tabs or tool box ....any info please help....again thanx to all..........safe ridin....52 gonzo...